Parts & Service / Mini Crawler Cranes

Mini Crawler Crane Repair & Troubleshooting Guide

Find troubleshooting guidance for hydraulic, electrical, power, safety and travel system issues.

Repair & Troubleshooting Guide

Select the affected system below to find common symptoms, possible causes, and recommended first checks for your GLT LIFTS mini crawler crane.

  1. 1Select the affected system
  2. 2Open the matching symptom
  3. 3Follow the recommended first checks

Hydraulic & Lifting System Issues

01Slow boom movement or insufficient lifting force

Possible Causes: Low hydraulic oil, hydraulic leakage, pump wear.

Recommended Solutions:

1. Check hydraulic level and refill fluid if necessary.

2. Inspect hydraulic lines, fittings, and seals for leaks.

3. Contact technical support for pump inspection.

02Hydraulic oil leakage

Possible Causes: Damaged hose, loose fitting, worn O-ring.

Recommended Solutions:

1. Stop machine and locate exact leakage point.

2. Tighten loose fittings or replace damaged O-rings.

3. Top up hydraulic oil to specified level after repair.

03Boom or outrigger slowly drifts down

Possible Causes: Worn cylinder seals, faulty counterbalance valve.

Recommended Solutions:

1. Lower load safely and support outriggers on firm ground.

2. Inspect hydraulic cylinder holding valves.

3. Contact GLT LIFTS team for valve testing.

Electrical & Remote Control Issues

01Wireless Remote Control Does Not Respond or Cannot Pair

Check the emergency stops and transmitter battery. For pairing steps, use the exact model’s operator’s manual; do not use an unverified button sequence. Contact GLT if the fault remains.

02Control Panel / Main Power Does Not Power On

Power-system checks vary by model. Do not probe or jump-start unless the operator’s manual permits it. Record the model and fault code and contact GLT or a qualified technician.

03Remote Control Signal Loss / Unstable Connection

Possible Causes:

  • Low transmitter battery causing RF power degradation.
  • Physical blockages (dense steel structures, thick concrete walls) or high-voltage power line interference nearby.
  • Damaged coaxial cable between receiver and antenna.

Recommended Solutions:

1. Replace Transmitter Battery: Weak batteries reduce transmission range before showing a low-battery alert.

2. Clear Line of Sight: Relocate position to ensure direct line-of-sight to the crane antenna; step away from large metal shielding or high-voltage lines.

3. Inspect Receiver Antenna: Check antenna connection cable for cuts, moisture ingress, or looseness. Tighten or replace antenna if necessary.

Safety System & Alarm Issues

01LMI Alarm / Load Moment Indicator Warning

Stop lifting if the LMI alarms. Follow the exact model’s operator’s manual to lower the load safely; do not move the boom unless the manual identifies that movement as safe.

02Outrigger Sensor Alarm / Machine Not Level

Level and alarm limits vary by model. Follow the operator’s manual and displayed instructions; do not use a generic angle threshold. Stop if the machine cannot be set up within its limits.

03Emergency Stop / Safety Interlock Activated (Machine Locked)

Check whether an emergency stop is engaged and read the displayed fault. Do not bypass the interlock. Follow the exact model’s operator’s manual and contact GLT if the cause is not clear.

Engine & Power System Issues

01Engine is difficult to start

Possible Causes:

  • Starter battery voltage depleted.
  • Fuel system empty, clogged fuel filter, or air trapped in fuel lines (diesel models).
  • Dual-Power (Diesel/Electric) selector switch set to incorrect mode.
  • Starter relay fault or neutral/safety interlock engaged.

Recommended Solutions:

1. Verify Power Selector: Check dual-power selector switch to ensure it matches power source being used (Engine vs. Motor).

2. Check Fuel & Bleed Air: Check fuel gauge/tank. If ran dry previously, prime fuel pump and bleed air out of diesel lines.

3. Test Battery & Starter: Jump-start or charge starter battery. Listen for starter solenoid "click" sound when turning key.

02Engine Starts but Stalls / Low Power Under Load

Possible Causes:

  • inadequate fuel supply volume.
  • Fuel filter blocked with dirt/water
  • Air intake filter heavily clogged with dust/debris.
  • Hydraulic system relief pressure set too high or hydraulic main pump over-loaded/jammed.

Recommended Solutions:

1. Inspect Fuel & Air Filters: Clean air filter element; drain fuel-water separator bowl and replace fuel filter element if contaminated.

2. Check Hydraulic Load: Ensure all control valve levers are neutral when starting; check hydraulic oil level and oil cooler clean state.

3. Quality Fuel Use: Ensure clean diesel fuel rated for current local ambient temperatures is used.

03Insufficient Battery Power / Charging System Failure

Charging checks and voltage ranges depend on the model and battery. Follow the operator’s manual; have a qualified technician test the system and contact GLT with the model and fault code.

Travel & Undercarriage Issues

01One Track Does Not Move / Crane Pulls to One Side

Stop travel if a track does not move or the crane pulls to one side. Do not raise the machine or swap hydraulic lines unless the exact model’s service procedure permits it; contact GLT.

02Machine Cannot Travel / Slow Travel Speed

Before travel, place the boom and outriggers in the transport position specified in the exact model’s operator’s manual. Contact GLT if the travel interlock remains active.

03Track Slippage / Track Tension Issues

Track-tension limits and adjustment steps vary by model. Use the exact service manual and have qualified service personnel perform the adjustment; contact GLT if the specification is unavailable.

Stop operation if a fault affects safe use. Do not bypass safety devices. If the issue persists, contact GLT LIFTS technical support with the model and serial number.

FAQ

Maintenance & Ownership FAQs

Common questions on service intervals, parts, cold-weather operation, training and storage.

What is the estimated total cost of ownership (TCO) for a mini crawler crane over the first 5 years?

Maintenance intervals and ownership costs depend on the exact model and use. Follow its maintenance schedule and request current service requirements from GLT; do not assume a resale value or ROI.

Can I use third-party hydraulic filters and oils without voiding the GLT LIFTS warranty?

Use fluids and filters listed for the exact model in its operator’s manual. Ask GLT how non-listed parts may affect the written warranty; do not assume coverage or exclusion.

How does the mini crawler crane’s safety system (LMI) perform in extreme North American weather conditions?

LMI operation and temperature limits vary by model. Follow the operator’s manual and confirm cold-weather procedures with GLT before lifting.

What level of specialized training is required for my team to perform routine crane maintenance?

Maintenance tasks and service requirements vary by model. Follow its operator’s manual and ask GLT which work requires a qualified technician and what support is available for your location.

What are the best practices for long-term storage if the crane is inactive for several months?

Storage steps and intervals vary by model and power system. Follow the exact model’s operator’s manual and confirm battery, fuel and hydraulic-system requirements with GLT.

See all mini crawler crane FAQs

Engineering Support for Mini Crawler Crane Systems

If the issue is not covered in this troubleshooting guide, our technical team can help assess hydraulic, electrical, and load-control systems and recommend the next service step.

Request Engineering Support